View AAT3110IGU-45-T1_616287.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AAT3110
MicroPowerTM Regulated Charge Pump General Description
The AAT3110 ChargePump is a member of AnalogicTech's Total Power Management ICTM (TPMICTM) product family. It is a MicroPower switched capacitor voltage converter that delivers a regulated output. No external inductor is required for operation. Using three small capacitors, the AAT3110 can deliver up to 100mA to the voltage regulated output. The AAT3110 features very low quiescent current and high efficiency over a large portion of its load range, making this device ideal for battery-powered applications. Furthermore, the combination of few external components and small package size keeps the total converter board area to a minimum in space-restricted applications. The AAT3110 operates in an output regulated voltage doubling mode. The regulator uses a pulse skipping technique to provide a regulated output from a varying input supply. The AAT3110 contains a thermal management circuit to protect the device under continuous output short-circuit conditions. The AAT3110 is available in a Pb-free, surfacemount 6-pin SOT23 or 8-pin SC70JW package and is rated over the -40C to +85C temperature range.
Features
* *
ChargePumpTM SmartSwitch
* * *
*
* * * * * *
Step-Up Voltage Converter Input Voltage Range: -- AAT3110-5: 2.7V to 5V -- AAT3110-4.5: 2.7V to 4.5V MicroPower Consumption: 13A Regulated 5V, 4.5V 4% Output 5V Output Current: -- 100mA with VIN 3.0V -- 50mA with VIN 2.7V 4.5V Output Current: -- 100mA with VIN 3.0V -- 50mA with VIN 2.7V Peak Current 250mA for 100ms High Frequency 750kHz Operation Shutdown Mode Draws Less Than 1A Short-Circuit/Over-Temperature Protection 2kV ESD Rating SC70JW-8 or SOT23-6 Package
Applications
* * * * * * * Cellular Phones Digital Cameras Handheld Electronics LED/Display Backlight Driver LEDs for Camera Flash PDAs Portable Communication Devices
Typical Application
AAT3110
VOUT
COUT
VOUT
C+
1F
10F
GND
VIN
VIN
CIN
ON/OFF
SHDN
C-
10F
3110.2005.11.1.4
1
AAT3110
MicroPowerTM Regulated Charge Pump Pin Descriptions
Pin #
SOT23-6 SC70JW-8
Symbol
VOUT GND SHDN CVIN C+
Function
Regulated output pin. Bypass this pin to ground with a 6.8F (min) low equivalent series resistance (ESR) capacitor. Ground connection. Shutdown input. Logic low signal disables the converter. Flying capacitor negative terminal. Input supply pin. Bypass this pin to ground with a 6.8F (min) low-ESR capacitor. Flying capacitor positive terminal.
1 2 3 4 5 6
1 2, 3, 4 5 6 7 8
Pin Configuration
SOT23-6 VOUT GND SHDN
1 6
SC70JW-8 C+ VIN CVOUT GND GND GND
1 2 3 4 8 7 6 5
2
5
3
4
C+ VIN CSHDN
2
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump Absolute Maximum Ratings1
TA = 25C, unless otherwise noted. Symbol
VIN VOUT VSHDN tSC TJ TLEAD VESD
Description
VIN to GND VOUT to GND SHDN to GND Output to GND Short-Circuit Duration Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec) ESD Rating2 -- HBM
Value
-0.3 to 6 -0.3 to 6 -0.3 to 6 Indefinite -40 to 150 300 2000
Units
V V V s C C V
Thermal Information3
Symbol
JA PD
Description
Maximum Thermal Resistance Maximum Power Dissipation
Rating
150 667
Units
C/W mW
1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. 3. Mounted on an FR4 board. 3110.2005.11.1.4
3
AAT3110
MicroPowerTM Regulated Charge Pump Electrical Characteristics
TA = -40C to +85C, unless otherwise noted. Typical values are at TA = 25C, CFLY = 1F, CIN = 10F, COUT = 10F. Symbol Description Conditions
VOUT = 5.0V 2.7V < VIN < 5V, IOUT = 0mA, SHDN = VIN 2.7V < VIN < 5V, IOUT 50mA 3.0V < VIN < 5V, IOUT 100mA 2.7V < VIN < 3.6V, IOUT = 0mA, VSHDN = 0 3.6V < VIN < 5V, IOUT = 0mA, VSHDN = 0 VIN = 2.7V, IOUT = 50mA VIN = 3V, IOUT = 100mA VIN = 2.7V, IOUT = 50mA Oscillator Free Running
Min
2.7 4.8 4.8
Typ
Max
VOUT 30 5.2 5.2 1 2.5
Units
V A V A mVP-P % kHz V V A A ms mA V A V A mVP-P % kHz V V A A ms mA
AAT3110-5 VIN Input Voltage IQ No Load Supply Current1 VOUT ISHDN VRIPPLE Output Voltage Shutdown Supply Current Ripple Voltage
13 5.0 5.0 0.01 25 30 92 750
Efficiency fOSC Frequency VIH SHDN Input Threshold High VIL SHDN Input Threshold Low IIH SHDN Input Current High IIL SHDN Input Current Low tON VOUT Turn-On Time ISC Short-Circuit Current2 AAT3110-4.5 VIN Input Voltage IQ No Load Supply Current3 VOUT ISHDN VRIPPLE fOSC VIH VIL IIH IIL tON ISC Output Voltage Shutdown Supply Current Ripple Voltage Efficiency Frequency SHDN Input Threshold High SHDN Input Threshold Low SHDN Input Current High SHDN Input Current Low VOUT Turn-On Time Short-Circuit Current2
1.4 SHDN = VIN SHDN = GND VIN = 3V, IOUT = 0mA VIN = 3V, VOUT = GND, SHDN = 3V VOUT = 4.5V 2.7V < VIN < 4.5V, IOUT = 0mA, SHDN = VIN 2.7V < VIN < 4.5V, IOUT 50mA 3.0V < VIN < 4.5V, IOUT 100mA 2.7V < VIN < 3.6V, IOUT = 0mA, VSHDN = 0 3.6V < VIN < 4.5V, IOUT = 0mA, VSHDN = 0 VIN = 2.7V, IOUT = 50mA VIN = 3V, IOUT = 100mA VIN = 2.7V, IOUT = 50mA Oscillator Free Running -1 -1 0.2 300 2.7 4.32 4.32 13 4.5 4.5 0.01 25 30 83 750 1.4 SHDN = VIN SHDN = GND VIN = 3V, IOUT = 0mA VIN = 3V, VOUT = GND, SHDN = 3V -1 -1 0.2 300 0.3 1 1 VOUT 30 4.68 4.68 1 2.5 0.3 1 1
1. VOUT is pulled up to 5.5V to prevent switching. 2. Under short-circuit conditions, the device may enter over-temperature protection mode. 3. VOUT is pulled up to 5.0V to prevent switching.
4
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump Typical Characteristics -- AAT3110-5V
Unless otherwise noted, VIN = 3V, CIN = COUT = 10F, CFLY = 1F, TA = 25C. Output Voltage vs. Output Current
5.15 22
Supply Current vs. Supply Voltage
Output Voltage (V)
VIN = 3.6V
Supply Current (A)
5.1 5.05 5 4.95 4.9 4.85 4.8 0 50
20 18 16 14 12 10 8 2.5
IOUT = 0A CFLY = 1F VSHDN = VIN
VIN = 3.0V VIN = 2.7V VIN = 3.3V
100
150
3
3.5
4
4.5
5
5.5
Output Current (mA)
Supply Voltage (V)
Supply Current vs. VSHDN
30 95
Efficiency vs. Supply Voltage
25mA
IOUT = 0A Supply Current (A)
25
90
Efficiency (%)
85 80 75 70 65 60 55 50 45 2.70 3.00 3.50 4.00 4.50 5.00
20
VIN = 5.5V
15 10 5 0 0 1 2 3 4 5
50mA 100mA
VIN = 2.8V
VIN = 3.3V
Supply Voltage (V)
VSHDN Control Voltage (V)
Efficiency vs. Load Current
100 90 80
Oscillator Frequency vs. Supply Voltage
Oscillator Frequency (kHz)
1200 1100 1000 900 800 700 600 500 400 2.7
VIN = 2.7V
Efficiency (%)
- 40C
70 60 50 40 30 20 10 0 0.01 0.1 1 10 100 1000
VIN = 3.6V VIN = 3.3V
VIN = 3.0V
25C 85C
3.0 3.5 4.0 4.5 5.0
Load Current (mA)
Supply Voltage (V)
3110.2005.11.1.4
5
AAT3110
MicroPowerTM Regulated Charge Pump Typical Characteristics -- AAT3110-5V
Unless otherwise noted, VIN = 3V, CIN = COUT = 10F, CFLY = 1F, TA = 25C. Startup Time with 50mA Load Startup Time with 100mA Load
SHDN (2V/div)
SHDN (2V/div)
VOUT (1V/div)
VOUT (1V/div)
Time (50s/div)
Time (50s/div)
Load Transient Response for 50mA
IOUT 0mA to 50mA (20mA/div) VIN = 3.0V VOUT AC Coupled (20mV/div) Time (50s/div) VOUT AC Coupled (20mV/div) IOUT 0mA to 100 mA (50mA/div)
Load Transient Response for 100mA
VIN = 3.0V
Time (50s/div)
Output Ripple with IOUT = 50mA
Output Ripple with IOUT = 100mA
VOUT AC Coupled (10 mV/div)
VOUT AC Coupled (10 mV/div) VIN = 3.0V Time (2s/div) VIN = 3.0V
Time (2s/div)
6
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump Typical Characteristics -- AAT3110-5V
Unless otherwise noted, VIN = 3V, CIN = COUT = 10F, CFLY = 1F, TA = 25C. Output Voltage vs. Input Voltage
(IOUT = 250mA)
5.2
Output Voltage (V)
4.8
-20C 20C 55C one shot pulse t = 100ms
4.4
4
3.6
3.2 3.2 3.4 3.6 3.8 4 4.2
Input Voltage (V)
3110.2005.11.1.4
7
AAT3110
MicroPowerTM Regulated Charge Pump Typical Characteristics -- AAT3110-4.5V
Unless otherwise noted, VIN = 3V, CIN = COUT = 10F, CFLY = 1F, TA = 25C. Output Voltage vs. Output Current
4.54
Supply Current vs. Supply Voltage
18
3.6V Output Voltage (V)
4.53
Supply Current (A)
17 16 15 14 13 12 11 10 2.5 3 3.5 4 4.5
4.52
No Load, Switching
2.7V
4.51 4.5 4.49 0.1 1 10 100 1000
3.0V 3.3V
No Load, No Switching
Output Current (mA)
Supply Voltage (V)
Supply Current vs. VSHDN
30 85
Efficiency vs. Supply Voltage
IOUT = 0A Supply Current (A)
25
80
Efficiency (%)
75 70 65 60 55
20
100mA 50mA 5mA
VIN = 5.5V
15 10 5
VIN = 2.8V
VIN = 3.3V
50 0 0 1 2 3 4 5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5
Supply Voltage (V)
VSHDN Control Voltage (V)
Efficiency vs. Load Current
85 80
Oscillator Frequency vs. Supply Voltage
Oscillator Frequency (kHz)
1200 1100 1000 900 800 700 600 500 400 2.7
Efficiency (%)
VIN = 2.7V
- 40C
75 70 65 60 0.1 1 10 100 1000
VIN = 3.0V VIN = 3.3V
25C 85C
3.0 3.5 4.0 4.5 5.0
Load Current (mA)
Supply Voltage (V)
8
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump Typical Characteristics -- AAT3110-4.5V
Unless otherwise noted, VIN = 3V, CIN = COUT = 10F, CFLY = 1F, TA = 25C. Load Transient Response
(VIN = 2.7V)
Load Transient Response
(VIN = 3.0V)
IOUT (100mA/div)
IOUT (100mA/div)
VOUT (20mV/div)
VOUT (20mV/div)
Time (50s/div)
Time (50s/div)
Output Ripple
(IOUT = 50mA @ VIN = 2.7V)
Output Ripple
(IOUT = 100mA @ VIN = 3.0V)
VOUT AC Coupled (5mV/div)
VOUT AC Coupled (5mV/div)
Time (5s/div)
Time (5s/div)
Output Voltage vs. Input Voltage for Pulsed High Current
Maximum Current Pulse (mA)
4.6 4.5 4.4 4.3 4.2 4.1 4 3 3.2 3.4 3.6 3.8 4 4.2
Maximum Current Pulse vs. Input Voltage
600 500 400 300 200 100 0 3 3.2 3.4 3.6 3.8 4 4.2
Output Voltage (V)
One-shot pulse duration = 50ms IOUT = 250mA
One-shot pulse duration = 50ms VOUT > 4.0V
Input Voltage (V)
Input Voltage (V)
3110.2005.11.1.4
9
AAT3110
MicroPowerTM Regulated Charge Pump Typical Characteristics -- AAT3110-4.5V
Unless otherwise noted, VIN = 3V, CIN = COUT = 10F, CFLY = 1F, TA = 25C. Startup
SHDN (1V/div) ILOAD = 150mA @ VIN = 3.3V
ILOAD = 100mA @ VIN = 3.0V VOUT (2V/div) ILOAD = 50mA @ VIN = 2.7V Time (100s/div)
10
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump Typical Characteristics -- AAT3110
Unless otherwise noted, VIN = 3V, CIN = COUT = 10F, CFLY = 1F, TA = 25C. SHDN Input Threshold (high) vs. Input Voltage
0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.60 0.55 0.50 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
SHDN Input Threshold (high) (V)
SHDN Input Threshold (low) vs. Input Voltage
SHDN Input Threshold (low) (V)
1.00 0.95 0.90 0.85 0.80 0.75 0.70 0.65 0.60 0.55 0.50 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
1.00
-40C 25C
-40C 25C
85C
85C
Input Voltage (V)
Input Voltage (V)
VSHDN Threshold vs. Input Voltage
1.00 0.95
Normalized Output Voltage vs. Temperature
Normalized Output Voltage (%)
1.20 1.00 0.80 0.60 0.40 0.20 0.00 -0.20 -0.40 -0.60 -50 -25 0 25 50 75 100 125
IOUT = 25mA
VSHDN Threshold (V)
0.90 0.85 0.80 0.75 0.70 0.65 0.60 0.55 0.50 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
VIH
VIL
Temperature (C)
Input Voltage (V)
3110.2005.11.1.4
11
AAT3110
MicroPowerTM Regulated Charge Pump Functional Block Diagram
VIN S2
SHDN
CONTROL
S1
C+ C-
VREF
S4
S3 VOUT
+
GND
Functional Description
Operation (Refer to block diagram)
The AAT3110 uses a switched capacitor charge pump to boost an input voltage to a regulated output voltage. Regulation is achieved by sensing the charge pump output voltage through an internal resistor divider network. A switched doubling circuit is enabled when the divided output drops below a preset trip point controlled by an internal comparator. The charge pump switch cycling enables four internal switches at two non-overlapping phases. During the first phase, switches S1 and S4 are switched on (short) and switches S2 and S3 are off (open). The flying capacitor CFLY is charged to a level approximately equal to input voltage VIN. During the second phase, switches S1 and S4 are turned off (open) and switches S2 and S3 are turned on (short). The low side of the flying capacitor CFLY is connected to GND during the first phase. During the second phase, the flying capacitor CFLY is switched so that the low side is connected to VIN. The voltage at the high side of the flying capacitor CFLY is bootstrapped to 2 x VIN and is connected to output through a switch. For each cycle phase, charge from input node VIN is transported from a lower voltage to a higher voltage. This cycle repeats itself until the output node voltage is high enough to exceed the preset input threshold of the control comparator. When the output voltage exceeds the internal trip point level, the switching 12
cycle stops and the charge pump circuit is temporarily placed in an idle state. When idle, the AAT3110 has a quiescent current of 13A or less. The closed loop feedback system containing the voltage sense circuit and control comparator allows the AAT3110 to provide a regulated output voltage to the limits of the input voltage and output load current. The switching signal, which drives the charge pump, is created by an integrated oscillator within the control circuit block. The free-running charge pump switching frequency is approximately 750kHz. The switching frequency under an active load is a function of VIN, VOUT, COUT, and IOUT. For each phase of the switching cycle, the charge transported from VIN to VOUT can be approximated by the following formula: VPHASE CFLY x (2 x VIN - VOUT) The relative average current that the charge pump can supply to the output may be approximated by the following expression: IOUT(AVG) CFLY x (2 x VIN - VOUT) x FSW The AAT3110 has complete output short-circuit and thermal protection to safeguard the device under extreme operating conditions. An internal thermal protection circuit senses die temperature and will shut down the device if the internal junction temperature exceeds approximately 145C. The charge pump will remain disabled until the fault condition is relieved.
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump Applications Information
External Capacitor Selection
Careful selection of the three external capacitors CIN, COUT, and CFLY is very important because they will affect turn-on time, output ripple, and transient performance. Optimum performance will be obtained when low ESR ceramic capacitors are used. In general, low ESR may be defined as less than 100m. If desired for a particular application, low ESR tantalum capacitors may be substituted; however, optimum output ripple performance may not be realized. Aluminum electrolytic capacitors are not recommended for use with the AAT3110 due to their inherent high ESR characteristic. Typically as a starting point, a capacitor value of 10F should be used for CIN and COUT with 1F for CFLY when the AAT3110 is used under maximum output load conditions. Lower values for CIN, COUT, and CFLY may be utilized for light load current applications. Applications drawing a load current of 10mA or less may use a CIN and COUT capacitor value as low as 1F and a CFLY value of 0.1F. CIN and COUT may range from 1F for light loads to 10F or more for heavy output load conditions. CFLY may range from 0.01F to 2.2F or more. If CFLY is increased, COUT should also be increased by the same ratio to minimize output ripple. As a basic rule, the ratio between CIN, COUT, and CFLY should be approximately 10 to 1. The compromise for lowering the value of CIN, COUT, and the flying capacitor CFLY is that the output ripple voltage may be increased. In any case, if the external capacitor values deviate greatly from the recommendation of CIN = COUT = 10F and CFLY = 1F, the AAT3110 output performance should be evaluated to assure the device meets application requirements. In applications where the input voltage source has very low impedance, it is possible to omit the CIN capacitor. However, if CIN is not used, circuit performance should be evaluated to assure desired operation is achieved. Under high peak current operating conditions that are typically experienced during circuit start-up or when load demands create a large inrush current, poor output voltage regulation can result if the input supply source impedance is high or if the value of CIN is too low. This situation can be remedied by increasing the value of CIN.
Capacitor Characteristics
Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the AAT3110. Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor typically has very low ESR, is lower cost, has a smaller PCB footprint, and is non-polarized. Low ESR ceramic capacitors help maximize charge pump transient response. Since ceramic capacitors are non-polarized, they are not prone to incorrect connection damage. Equivalent Series Resistance: ESR is a very important characteristic to consider when selecting a capacitor. ESR is a resistance internal to a capacitor that is caused by the leads, internal connections, size or area, material composition, and ambient temperature. Typically, capacitor ESR is measured in milliohms for ceramic capacitors and can range to more then several ohms for tantalum or aluminum electrolytic capacitors. Ceramic Capacitor Materials: Ceramic capacitors less than 0.1F are typically made from NPO or C0G materials. NPO and C0G materials typically have tight tolerance and are very stable over temperature. Large capacitor values are typically composed of X7R, X5R, Z5U, or Y5V dielectric materials. Large ceramic capacitors, typically greater than 2.2F, are often available in low-cost Y5V and Z5U dielectrics. If these types of capacitors are selected for use with the charge pump, the nominal value should be doubled to compensate for the capacitor tolerance which can vary more than 50% over the operating temperature range of the device. A 10F Y5V capacitor could be reduced to less than 5F over temperature; this could cause problems for circuit operation. X7R and X5R dielectrics are much more desirable. The temperature tolerance of X7R dielectric is better than 15%. Capacitor area is another contributor to ESR. Capacitors that are physically large will have a lower ESR when compared to an equivalent material smaller capacitor. These larger devices can improve circuit transient response when compared to an equal value capacitor in a smaller package size.
Charge Pump Efficiency
The AAT3110 is a regulated output voltage doubling charge pump. The efficiency () can simply 13
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump
be defined as a linear voltage regulator with an effective output voltage that is equal to two times the input voltage. Efficiency () for an ideal voltage doubler can typically be expressed as the output power divided by the input power. POUT PIN charge pump switching cycle operation. The thermal limit system has 10C of system hysteresis before the charge pump can reset. Once the overcurrent event is removed from the output and the junction temperature drops below 135C, the charge pump will become active again. The thermal protection system will cycle on and off if an output short-circuit condition persists. This will allow the AAT3110 to operate indefinitely under short-circuit conditions without damaging the device.
=
In addition, with an ideal voltage doubling charge pump, the output current may be expressed as half the input current. The expression to define the ideal efficiency () can be rewritten as: POUT VOUT x IOUT V = = OUT PIN VIN x 2IOUT 2VIN
Output Ripple and Ripple Reduction
There are several factors that determine the amplitude and frequency of the charge pump output ripple, the values of COUT and CFLY, the load current IOUT, and the level of VIN. Ripple observed at VOUT is typically a sawtooth waveform in shape. The ripple frequency will vary depending on the load current IOUT and the level of VIN. As VIN increases, the ability of the charge pump to transfer charge from the input to the output becomes greater. As it does, the peak-to-peak output ripple voltage will also increase. The size and type of capacitors used for CIN, COUT, and CFLY have an effect on output ripple. Since output ripple is associated with the R/C charge time constant of these two capacitors, the capacitor value and ESR will contribute to the resulting charge pump output ripple. This is why low ESR capacitors are recommended for use in charge pump applications. Typically, output ripple is not greater than 30mVP-P when VIN = 3.0V, VOUT = 5.0V, COUT = 10F, and CFLY = 1F. When the AAT3110 is used in light output load applications where IOUT < 10mA, the flying capacitor CFLY value can be reduced. The reason for this effect is when the charge pump is under very light load conditions, the transfer of charge across CFLY is greater during each phase of the switching cycle. The result is higher ripple seen at the charge pump output. This effect will be reduced by decreasing the value of CFLY. Caution should be observed when decreasing the flying capacitor. If the output load current rises above the nominal level for the reduced CFLY value, charge pump efficiency can be compromised. There are several methods that can be employed to reduce output ripple depending upon the requirements of a given application. The most simple and straightforward technique is to increase the value of
= -or-
(%) = 100
VOUT 2VIN
For a charge pump with an output of 5.0V and a nominal input of 3.0V, the theoretical efficiency is 83.3%. Due to internal switching losses and IC quiescent current consumption, the actual efficiency can be measured at 82.7%. These figures are in close agreement for output load conditions from 1mA to 100mA. Efficiency will decrease as load current drops below 0.05mA or when the level of VIN approaches VOUT. Refer to the Typical Characteristics section of this datasheet for measured plots of efficiency versus input voltage and output load current for the given charge pump output voltage options.
Short-Circuit and Thermal Protection
In the event of a short-circuit condition, the charge pump can draw a much as 100mA to 400mA of current from VIN. This excessive current consumption due to an output short-circuit condition will cause a rise in the internal IC junction temperature. The AAT3110 has a thermal protection and shutdown circuit that continuously monitors the IC junction temperature. If the thermal protection circuit senses the die temperature exceeding approximately 145C, the thermal shutdown will disable the 14
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump
the COUT capacitor. The nominal 10F COUT capacitor can be increased to 22F or more. Larger values for the COUT capacitor (22F and greater) will by nature have lower ESR and can improve both high and low frequency components of the charge pump output ripple response. If a higher value tantalum capacitor is used for COUT to reduce low frequency ripple elements, a small 1F low ESR ceramic capacitor should be added in parallel to the tantalum capacitor (see Figure 1). The reason for this is tantalum capacitors typically have higher ESR than equivalent value ceramic capacitors and are less able to reduce high frequency components of the output ripple. The only disadvantage to using large values for the COUT capacitor is the AAT3110 device turn-on time and inrush current may be increased. If additional ripple reduction is desired, an R/C filter can be added to the charge pump output in addition to the COUT capacitor (see Figure 2). An R/C filter will reduce output ripple by primarily attenuating high frequency components of the output ripple waveform. The low frequency break point for the R/C filter will significantly depend on the capacitor value selected.
Layout Considerations
High charge pump switching frequencies and large peak transient currents mandate careful printed circuit board layout. As a general rule for charge pump boost converters, all external capacitors should be located as closely as possible to the device package with minimum length trace connections. Maximize the ground plane around the AAT3110 charge pump and make sure all external capacitors are connected to the immediate ground plane. A local component side ground plane is recommended. If this is not possible due to layout design limitations, assure good ground connections by the use of large or multiple PCB vias. Refer to the AAT3110 evaluation board for an example of good charge pump layout design (Figures 3 through 5).
VOUT (5V)
COUT2 1F
COUT1 22F
+
VOUT
C+ CFLY 1F
+
AAT3110-5
GND VIN
VIN (2.7V to 5V)
CIN 10F
ON/OFF
SHDN
C-
Figure 1: Application Using Tantalum Capacitor.
VOUT (5V)
RFILTER 1.5
VOUT
CFILTER 33F
C+ CFLY 1F
COUT 10F
AAT3110-5
GND VIN
VIN (2.7V to 5V)
CIN 10F
ON/OFF
SHDN
C-
Figure 2: Application With Output Ripple Reduction Filter.
3110.2005.11.1.4
15
AAT3110
MicroPowerTM Regulated Charge Pump
Figure 3: Evaluation Board Top Side Silk Screen Layout / Assembly Drawing.
Figure 4: Evaluation Board Component Side Layout.
Figure 5: Evaluation Board Solder Side Layout.
Typical Application Circuits
VOUT (5V)
VOUT
C+ CFLY 1F CIN 10F
COUT 10F
AAT3110-5
GND
VIN
VIN (2.7V to 5V)
ON/OFF
SHDN
C-
Figure 6: Typical Charge Pump Boost Converter Circuit.
CFLY 1F
C-
C+
VIN (USB Port VOUT)
CIN 10F
VIN
SHDN
VOUT
VOUT 5V 100mA
COUT 10F
AAT3110-5
GND
GND (USB Port Return)
Figure 7: 5V, 100mA Supply Powered From a USB Port.
GND
16
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump
VIN
Li-Ion Battery 2.7V to 4.2V 10F
VOUT
C+
10F 1F 120 120 120 120
AAT3110-5
SHDN C-
ON/OFF
Figure 8: 5V LED or Display Driver from a Li-Ion Battery Source.
VIN = 3.0V to 5V
VIN
CIN 10F
VOUT
C+
VOUT = 5V IOUT = 200mA
AAT3110-5 (A)
SHDN GND C-
SHDN
CFLY 1F
VIN
VOUT
C+ COUT 10F
AAT3110-5 (B)
SHDN GND C-
CFLY 1F
Figure 9: 5V, 200mA Step-Up Supply from a 3V to 5V Source.
3110.2005.11.1.4
17
AAT3110
MicroPowerTM Regulated Charge Pump Ordering Information
Output Voltage
4.5V 5.0V 4.5V 5.0V
Package
SOT23-6 SOT23-6 SC70JW-8 SC70JW-8
Marking1
EEXYY ASXYY EEXYY ASXYY
Part Number (Tape and Reel)2
AAT3110IGU-4.5-T1 AAT3110IGU-5.0-T1 AAT3110IJS-4.5-T1 AAT3110IJS-5.0-T1
All AnalogicTech products are offered in Pb-free packaging. The term "Pb-free" means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/pbfree.
Package Information
SOT23-6
2.85 0.15 1.90 BSC 0.95 BSC
1.575 0.125
1.10 0.20
2.80 0.20 1.20 0.25
0.075 0.075
0.15 0.07 4 4
GAUGE PLANE
10 5 0.40 0.10 x 6
0.60 REF
0.45 0.15
0.10 BSC
All dimensions in millimeters.
1. XYY = assembly and date code. 2. Sample stock is generally held on all part numbers listed in BOLD.
18
3110.2005.11.1.4
AAT3110
MicroPowerTM Regulated Charge Pump
SC70JW-8
0.50 BSC 0.50 BSC 0.50 BSC
1.75 0.10 0.225 0.075 2.00 0.20
2.20 0.20
0.048REF 0.15 0.05
0.85 0.15
1.10 MAX
0.100
7 3
0.45 0.10 2.10 0.30
4 4
All dimensions in millimeters.
0.05 0.05
3110.2005.11.1.4
19
AAT3110
MicroPowerTM Regulated Charge Pump
(c) Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech's standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed.
Advanced Analogic Technologies, Inc.
830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 20
3110.2005.11.1.4

▲Up To Search▲

Price & Availability of AAT3110IGU-45-T1

	To Download AAT3110IGU-45-T1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .